• Address: Rm615, No.8 Building,Shengyu Industry Center
    No.365 Chuanhong road, Pudong, Shanghai

  • Call Us: (+86) 021-58211911
    [email protected]

Special Packaging Injection Molding Machine

Heat Transfer Oil Systems - Mokon Temperature Control Units

Mokon's circulating oil temperature control systems meet process heating requirements up to 700°F (371°C). Our durable and high-quality oil systems are available with heating capacities up to 600 kW; flow rates of 5 to 120 GPM; single, dual and triple zone configurations; and portable or stationary designs.

T Series Oil Temperature Control Unit | Hot Oil Unit

Features. Technical Info. Special Designs. 6 - 300 KW Heater. Maximum Operation Temperature of 550°F (288°C) 10 to 150 GPM Pumping Capacity. Heating Only or Heating and Cooling Capabilities. Our Delta T Systems' T Series Hot Oil Unit is available as a Single Zone or Dual Zone oil circulating high temperature control system. This hot oil unit is suitable for standard operation of up to 550° F (288° C).

Mold Temperature Controller | Mold Heaters

Delta T Systems' Temperature Control Units or 'mold heaters' can control small injection molds all the way up to molds weighing 50,000lbs. Precisely controlling the temperature of a mold is very important to insure quality moldings every time. Delta T Systems' units offer both heating and cooling capabilities to maintain a preset mold temperature. Making sure your mould temperature controller is properly …

Industrial Heated Temperature Control Units & Controllers ...

Design Temp: 400⁰F; Design Pressure: 150 PSIG; Rating (BTU/HR): 550,000 Heating & Cooling; Application: Furniture Molding Press; Equipment Features: Proportional Direct Inject Heating; Proportional Fin/Fan Cooling; Pre-Wired, Skid Mounted Design; Foam Glass Insulation

Temperature Control Units | Mokon Temperature Control Units

HTF 500 Series. Mokon's HTF 500 Series heat transfer oil systems are available up to 500°F (260°C) with a flow rate of either 10 GPM or 20 GPM in single…. View. HTF 600 Series. Mokon's HTF 600 Series heat transfer oil systems are designed to meet the high temperature demands of controlling process temperatures up….

Mold Temperature Controllers / temperature /temperature ...

High-precision temperature controller (PID controller), can accurately control and display the injection mold temperature within +- 1°C One-piece stainless steel (SUS-304) tank, for more durability Can use water or oil as medium, depending on needed mold temperature Automatic shut down and alarm upon low medium level

Temperature Control Units Industrial Process Temperature ...

OIL UNITS; Oil Temperature Control Units circulate high temperature heat transfer fluid through the process application for temperature control. Regal Series temperature control units offer temperature control from 100° to 500°F; Select From: Regal Units; Heater kW: 12 - 48; Pump HP: 1 - 7.5; Pump GPM: 30 - 100; Instrument: Regal G500 Series

Mold Heaters | McMaster-Carr

Choose from our selection of mold heaters, including over 1,200 products in a wide range of styles and sizes. In stock and ready to ship.

Thermolator® Temperature Control Units for Plastics ...

With incoloy heaters, silicon carbide pump seals, To Process and From Process pressure gauges, microprocessor controls and optional line purge, the TW-V offers big bang for the buck. ¾ Hp or 2 Hp pumps are available, with a 12 kW heater, for temperatures from 40-250°F {4-121°C}.

Plastics Industry Heat Transfer Equipment | Conair

Heat Transfer From Thermolator® temperature control units to central chillers, Conair’s Heat Transfer products are known for heavy-duty construction, user-friendly controls, reliable performance and one of the best warranties in the business.

Hot Oil Heating Systems - Heat Exchange and Transfer, Inc.

Thermal Fluid Systems SL Series Hot Oil Systems The SL Series of Heat Transfer Systems are designed for closed loop temperature control of high temperature heat transfer fluids. These completely packaged systems are designed for a maximum operating temperature of …

Cartridge Heaters - Industrial Heaters Wattco

Cartridge heaters will reach metal temperatures of up to 1,400ºF (760ºC) with the appropriate material, watt density, and fit selections (see Figure 2 on our catalog page 7.2). Get a quote on a cartridge heater today. WATTCO also manufactures other industrial heating products such as infrared heaters, immersion heaters, pipe heaters and more.

Industrial Process Heating - Technology Assessment

75 through a heat transfer mechanism. Steam heating accounts for a significant amount of the energy used 76 in lower temperature industrial process heating (<400 deg. F.). Use of steam based systems is largely for 77 industries where heat supply is at or below about 400 deg. F. …

Temperature Control Oil Unit Mold Max Electronics Power ...

Mold temperature machine consists of circuit control box, heater, heat exchanger (ie cooling system), liquid level controller, pressure limiter, temperature sensor, circulation pump and pipeline. Only when these components zd cooperate with each other, the mold temperature machine version can work normally and maximize its role.

Calrod Heaters - Industrial Heaters Wattco

They are also implemented in mold designs for aiding heat transfer to steel or aluminum mold from the Calrod heaters. You can get Calrod elements in many different shapes, and they are also available in four particular standard diameters mentioned in inches: 0.315, 0.375, 0.430 and 0.475.

oil mold temperature controller, oil mold temperature ...

Mould Temperature Controller Oil Mold Mold Heater Shini Mould Temperature Controller With Oil 6 ~ 36 KW Industrial Oil Heater For Mold Up To 300 Degree Celsius US $1278-$5950 / …

Controlling Hot Oil Temperatures in Plastic Applications

Nov 03, 2017 · Correctly applied hot-oil temperature control can maintain temperature within ± 1 °C. Using electrical resistance for heating and forced air for cooling, this degree of control is difficult. Faster Start-up. Using a hot oil system, the temperature in an extruder die or a mold can be raised up to temperature rapidly before production is started.

Author: Paratherm

oil mold heater, oil mold heater Suppliers and ...

6kw water circulating extruder plastic injection mold temperature controller machine. 315 oil mold heater products are offered for sale by suppliers on , of which mould temperature controller accounts for 40%, heating equipment accounts for 20%. A wide variety of oil mold heater options are available to you, such as electric.

Chromalox

Technical Resources. Chromalox hot oil and water systems are self-contained heating and cooling packages that provide direct or indirect process heating to temperatures of 750° F. These systems meet ASME codes and are pre-engineered to include temperature and power controls, expansion tanks, heat exchangers, pumps, valves, gauges, and all necessary piping.

Heat Transfer Systems | Budzar Industries

With environmentally friendly refrigerant achieves a temperature range of -85° to +200° C and is suitable for applications requiring a wide range of heating and cooling applications with a single heat transfer fluid.

Heat Transfer Fluids - XCELTHERM® Synthetic and Hot Oil ...

A high performing, low cost hot oil heat transfer fluid formulated for the die casting and injection molding industries. Xceltherm® DCT has excellent heat transfer efficiency and an extended operational life due to its inherent thermal stability. For use up to 600°F (315°C). Asphalt Industry Heat Transfer Fluids.

Water Temperature Controllers - Oil & Mold Temperature ...

Oiltherm RO Temperature Control Units. Designed to work with a wide range of high temperature applications in the 125°F to 575°F range. Oiltherm RO Series units assure high velocity oil flow across heater elements for optimum heat transfer and fluid life. Learn More

Hot oil heaters and thermal fluids: the complete guide ...

Most synthetic thermal fluids have a significant advantage over mineral oils in heat transfer efficiency at temperatures between 150°C and 260°C. Above this temperature range (up to 300°C), some mineral heat transfer fluids narrow the gap with highly refined paraffinic / naphthenic white oils.

Standard Water/ Oil Mold Temperature Controller - Buy …

Transfer Medium: Heat Transfer Oil: Maximum Temperature: 200°C: Pump (KW) 0.37: 0.75: 0.75: 1.5: 1.5: 2.2: Pump Flow (L/min) 42: 56: 56: 160: 160: 315: Loading Distance (m) 28: 38: 38: 27: 27: 30: Heating Power (KW) 6: 9: 12: 9*2: 12*2: 12*3: Inlet and Outlet Diameter: 3/8``x2: 3/8``x4: 3/8``x4: 1''x1: 1''x1: 1.5``x1: Dimensions (mm) 730*310*643: 730*310*643: 730*310*643: 830*370*694: …

Mold Temperature Controller | Budzar Industries

The Mold Temperature Controller is typically used in industrial applications where accurate temperature control is required. including injection molding, blow molding, and extrusion. The Budzar Industries Water Temperature Controller is the smallest, best performing, best priced unit on the market.

Sterling TCU - Oil | Oil Temperature Control Units

Mold Temperature Controllers (Oil); 2016C (Former Compact Series), Midsize, Upright High Temperature Heat Transfer, Specialty Oil Unit Sterling's Oil Temperature Control Units include the 2016C and 2016U Series, the 2016M Midsize Royal Series High Temperature Control System, and the 6017 Series High Temperature, High Capacity Specialty Oil Unit.

Home - Thermal Fluid Systems, Inc.

Thermal fluid ("hot oil") heating systems are used in many industrial applications where efficiency and accurate temperature control between 300° F and 750° F are required. TFS has many years' experience in this field and we offer a broad range of products, service and support. From initial concept, through design, engineering, and ...

China Cooling Tower manufacturer, Water Chiller, Heat …

Cooling Tower, Water Chiller, Heat Pump manufacturer / supplier in China, offering Injection Molding Dual System Heat Transfer Oil Electric Heater, Injection Molding Dual System Thermal Oil Mold Temperature Controller, Injection Molding High Temperature Hot Oil Electric Heating …

Industrial Oil Heater Mold Temperature Controller with CE

Industrial Oil Heater Mold Temperature Controller With CE The use of mold temperature machine in the plastic industry: 1, improve the product's molding efficiency; 2, reduce the production of defective products; 3, improve the appearance of the …

Controlling Hot Oil Temperatures in Plastic Applications

Nov 03, 2017 · Correctly applied hot-oil temperature control can maintain temperature within ± 1 °C. Using electrical resistance for heating and forced air for cooling, this degree of control is difficult. Faster Start-up. Using a hot oil system, the temperature in an extruder die or a mold can be raised up to temperature rapidly before production is started.

Wensui Mold Heater

P.I.D control adopted, keeping the mould temperature accurately (less than ± 0.5 ℃). The electrical and heating equipment was designed to be separated to avoid high temperature damage to machine. Used high quality and high efficiency pumps, applicable to all kinds of mould temperature …

Operating A Hot Oil Heat Transfer Fluid System

These increment steps are done by taking a system from 70°F (21°C) and increasing the heat by 20°F (11°C) and letting the system run until the temperature on the heater reads 90°F (32°C). Once the heater reads that then dial it up another 20°F (11°C). Once your heat transfer fluid is 10 cP or less, you can dial the heater to your ...

Thermoset Injection Mold Design Tips - Plenco

Jan 30, 2017 · the method of mold heating. A mold that is correctly designed and heated by steam or oil will have a uniform mold temperature because the heat source maintains a constant temperature. However, oil as a heat source is only about half as efficient as steam. Therefore, when using oil to heat a mold, it is necessary to set the oil temperature ...

Beat the Heat When Molding High-Temperature Thermoplastics ...

Sep 29, 2012 · Typically, circulating oil is required for high-heat plastics because the recommended tool temperature is higher than 125 C (257 F), which is well above the boiling point of water. However, pressurized water can be heated above the 100 C (212 F) boiling temperaure.

High temperature heat transfer fluid | Heat transfer ...

We offer a wide range of heat transfer fluids with different operating temperature ranges because we understand that every industrial process has specific temperature requirements. Our liquid phase heat transfer fluids are suitable for systems operating at 15°C to 400°C and our vapour phase heat transfer fluids can operate at 257°C to 400°C.

Industrial and Process Heating Elements | Temperature ...

Heating Elements. Heating Elements Plus provides a wide range of electric heating elements for industrial and process applications. We also sell heated hoses, drum heaters, tote heaters, tank heaters and silicone rubber heating pads and blankets. If you're needing a band heater, cartridge heater, bolt heater, coil heater, runnerless mold heater ...

HIGH TEMPERATURE HEAT TRANSFER THERMIC OIL - …

Dropping point, ASTM D 2265, oC. -36. Flash Point, deg C, ASTM D 92. 200. Pour Point, degree celsius, ASTM D 97. -36. Flash Point, degree celsius, ASTM D 92. 200. We are offering total seriola 1120/1510 synthetic thermic fluid oil like therminol 55 , hitech therm 60 and servo therm s, hytherm s, s k lubericants 300 , Brugarolas bestherm 3.

Mold Simulator Study of Heat Transfer Phenomenon During ...

Jan 03, 2017 · In this paper, mold simulator trials were firstly carried out to study the phenomena of the initial shell solidification of molten steel and the heat transfer across the initial shell to the infiltrated mold/shell slag film and mold. Second, a one-dimensional inverse heat transfer problem for solidification (1DITPS) was built to determine the temperature distribution and the heat transfer ...

Mobiltherm 603

In well-designed systems the temperature of the oil film surrounding the heating element should be about 15ºC to 30ºC above the bulk oil temperature. If higher than this, the service life of the oil may be shortened and sludge and coke may be deposited which would interfere with the heat transfer rates.

Understand Thermal Fluids & Thermal Fluid Systems | …

Dec 27, 2019 · Types of Heat Transfer Fluids. Thermal oil, water, and water-glycol solutions are all commonly used in thermal fluid heating systems. All of these heat transfer fluids offer various advantages and disadvantages depending on the operating temperature and …

Hot Oil Systems | Shini USA

Get to Know Our Hot Oil System Units. The Shini USA industrial temperature control hot oil systems are fluid circulating units that control the application temperatures. We offer both low-temperature (350°F) hot oil units and high-temperature (450°F) hot oil systems. With a one-gallon capacity, each hot oil unit features an Omron temperature ...

Oiltherm RO Series Temperature Controller - Oil ...

Hot Oil Temperature Controllers. Oiltherm RO Series units are designed to work with a wide range of high temperature applications in the 125°F to 575°F range. The Oiltherm assures high velocity oil flow across heater elements for optimum heat transfer and fluid life. The oil is preheated to reduce viscosity before allowing the pump to run.

Heat-Transfer and Solidification Model of Continuous …

Aug 27, 2002 · One of the greatest resistance to heat transfer from the liquid steel to the mold cooling water is the interface between the mold and shell. Heat transfer across this interface is controlled by the thickness and thermal properties of the materials that fill the …

Hot Oil Heaters | Heating Systems | Sigma Thermal

Hot Oil Heater. Sigma Thermal is an industry leader, providing modern hot oil heater systems, backed by decades of energy experience. Our expert engineering teams provide system design, custom manufacturing, troubleshooting and all related energy system controls for industrial clients worldwide.

Thermal oil heaters for hot oil heating systems | Pirobloc

Fuel savings up to 20% compared to steam heating systems. A thermal fluid system consists of a closed circuit with minimum energy leaks. At least 90% of the fuel is used in the heating process. Hot oil heating systems are highly efficient thanks to the temperature uniformity through all …

Heaters | Watlow

Watlow is a leader in the industrial heater industry manufacturing high quality cartridge heaters, immersion heaters, advanced ceramic heaters and other electric heaters. Socialize with us: 1-800-928-5692 ... High-temperature heaters offer ultra-fast ramp rates, precise temperature uniformity and high temperatures for applications requiring low ...

Mould Temperature Controllers Suppliers | PlastikCity

Oil TCU’s for applications up to 360°C with heating capacities from 3kW to 144kW. Tool-Temp offer a range of models for specialist applications where a very quick change of temperature is required between 30°C -160°C, units with very high cooling capacities, …

Mobiltherm 600 Series

In well-designed systems the temperature of the oil film surrounding the heating element should be about 15ºC to 30ºC above the bulk oil temperature. If higher than this, the service life of the oil may be shortened and sludge and coke may be deposited which would interfere with the heat transfer rates.

Industrial Water Chiller And Temperature Control Unit ...

Explosion proof grade: Exd II BT4 / Media: Heat transfer oil / Get The Full Solution And Quotation Details! CONTACT WITH AN ENGINEER NOW! LDS Machinery. The professional supplier focuses on industrial temperature control equipment production integrating with R&D, manufacturing, sales and customer service.

Design & Supply of High Efficiency Thermal Fluid Heating ...

For over a quarter of a century, Thermal Fluid Systems, Inc. has provided high-efficiency thermal fluid heating systems to process industries. Our process heaters can be operated indoors or outdoors. They have an output range of 0.5 to 50,000,000+ BTU/hour, as well as a lower heating …

China Industrial Temp Control Unit Tcu for Plastic ...

Plastic Mold Heater, Injection Mold Temperature Control Unit, Mould Temp Controller manufacturer / supplier in China, offering Industrial Temp Control Unit Tcu for Plastic Injection Machine Thermolator, Air Screw Chiller 100 Tons for Hydraulic Oil Temperature Control, 40 HP Chiller for Chilled Water System of Hydraulic Equipment and so on.

China 6kw Industrial Water Mold Temperature Controller ...

Mold Temperature Controller, Heating Temperature Controller, Heating Heater Temperature Controller manufacturer / supplier in China, offering 6kw Industrial Water Mold Temperature Controller, 18kw Oil Temperature Machine Heater Controller Unit for Plywood, Industrial Air Cooled Chiller Plant with Copeland Compressor and so on.

Mold Temperature Controller - Mould Temperature Controller ...

Find here Mold Temperature Controller, Mould Temperature Controller manufacturers, suppliers & exporters in India. Get contact details & address of companies manufacturing and supplying Mold Temperature Controller, Mould Temperature Controller, Digital Mold Temperature Controller …

Fuchs Industrial Heat Transfer Oil Suppliers in Dubai ...

Heat Transfer Oil is a highly refined and stable paraffinic oil designed to be used as a heat transfer medium. In many industrial applications heatings provided indirectly by circulating hot oil through a heat exchanger, thus reducing hot spots and increasing the safety of the heating process.

Mold Releases and Release Agents Selection Guide ...

Molding – Compression, injection, transfer, as well as many other application-specific molding operations rely on mold release agents as a processing aid in order to consistently produce desired shapes from a wide range of materials including composites, elastomers, thermoplastics, and …

Mold Water Heater-China Mold Water Heater …

6 ~ 36 Kw Industrial Water Mold Heater for Injection Molding. US $ 1,356.26-1,490.58 / set FOB. MOQ: 1 set. Since 2020. Contact Supplier. Nanjing Xingde Machinery Co., Ltd. Manufacturer/Factory & Trading Company. Jiangsu, China Since 2020. Chat Now Send Inquiry.

Industrial Lubricants | Chevron Lubricants (US)

Chevron HTF P-150 is a superior quality single phase, silicate free, propylene glycol concentrate used in heat transfer applications or as an industrial coolant/ antifreeze product. Chevron HTF P-200. Chevron HTF P-200 is a single phase, silicate free, propylene glycol (USP) based heat transfer fluid concentrate.

High Temp. High Pressure Water MTC - Buy Water heater mold ...

High Temp. High Pressure Water MTC, find complete details about High Temp. High Pressure Water MTC, Water heater mold temperature controller, High temperature water mold temperature controller, Water Temperature Control Units - Jiangmen Xiecheng Machinery Co., Ltd.

Submit Your Requirement Below For injection molding Proposal!